ForumUnread Topics

The Forum from now on is in READ ONLY mode. Thank you for participating, but this message board is being sunset.

Unread Topics

Tips for Improving Print Quality with CraftBotIn Tips and Tricks · 2 years ago

Choosing Printing Materials for Toy ModelsIn General Discussions · 2 years ago

Printing ProblemIn General Discussions · 2 years ago

New troubleIn Troubleshooting · 2 years ago

Buy 3D printer filament in bulkIn General Discussions · 2 years ago

Your Trusted Long Distance Movers in Las VegasIn Troubleshooting · 2 years ago

Exploring MoviezAddiction: A Comprehensive Overview of the Ultimate Streaming DestinationIn Troubleshooting · 2 years ago

Why craftbot don't develop corexy printer?In General Discussions · 2 years ago

Craftware pro v1.2.1.107 BIn General Discussions · 2 years ago

Ghosting in Craftbot Pro PLUSIn General Discussions · 2 years ago

Critical error starting Craftware ProIn Troubleshooting · 3 years ago

New version released: 1.2.1In Announcements and Releases · 3 years ago

Open-circuit on temperature sensorIn Troubleshooting · 2 years ago

From 3D Scanning to 3D PrintingIn General Discussions · 2 years ago

How many different models can CraftBot slice in a single session?In General Discussions · 2 years ago

How many models do craftbot support to slice in once?In General Discussions · 4 years ago

Which material is better for printing a house model?In General Discussions · 3 years ago

BL touch sensor errorIn General Discussions · 3 years ago

Avoid crossing perimetersIn Troubleshooting · 3 years ago

How can I make it easier to remove the support structures from my 3D prints?In General Discussions · 3 years ago

Chamber heaterIn General Discussions · 3 years ago

Beginner Guide for Legacy users moving to craftware pro?In Tips and Tricks · 5 years ago

Hint Preview for Craftware Pro??In General Discussions · 4 years ago

Error in G-code with my Craftbot XLIn Troubleshooting · 3 years ago

Craftbot 3 software upgradeIn General Discussions · 3 years ago

air fan no workIn General Discussions · 4 years ago

Cheat sheet for Start gcode variablesIn Tips and Tricks · 4 years ago

Retraction settings - where?In Troubleshooting · 3 years ago

Fuzzy area processIn General Discussions · 3 years ago

M106 S0 P0 and P1 commands error messageIn General Discussions · 3 years ago

Locking in Support on Head #2In Troubleshooting · 3 years ago

Does the filament dryer is a necessary tool for 3d printing？In General Discussions · 3 years ago

Overextrusion at deceleration zones, pressure advanceIn General Discussions · 3 years ago

Problem installing extruder and hot end on Craftbot 2In Troubleshooting · 3 years ago

Setting up support.In Troubleshooting · 3 years ago

Fatal ErrorIn General Discussions · 3 years ago

Setting up Printhead 2In Troubleshooting · 3 years ago

printing artefacts similar to Z-axis wobbleIn Troubleshooting · 3 years ago

I can't connect my printer to the printer management softwareIn Troubleshooting · 3 years ago

After Slicing everytime i got a Black Screen with Movable Mouse ArrowIn General Discussions · 3 years ago

Problem AnycubicIn Troubleshooting · 3 years ago

New version released: 1.2.0In Announcements and Releases · 4 years ago

Additional Profiles for FilamentsIn Support for Printers & Filaments · 4 years ago

Pillar loop countIn Troubleshooting · 3 years ago

Printing One Model at a TimeIn Troubleshooting · 3 years ago

Syntax Error?In Troubleshooting · 3 years ago

Craftbot Plus Bed HeightIn Troubleshooting · 3 years ago

Change calibration ordeIn Feature Requests · 3 years ago

Bad first Layer after calibrationIn Troubleshooting · 3 years ago

slicing strategy errorIn General Discussions · 3 years ago

Didn’t find what you want?
Submit a ticket →